Camera auto-motion

Instead of setting angles and paths in degrees, you describe what should be visible. Each area is a rectangle on a device’s display. The camera works out a viewpoint from it and travels from one to the next. This is for films only. In the editor, the result is called “Camera move”.

Drawing areas#

  1. Select a device and press A, and the editor switches to animation mode for it. Or right-click its track and choose “Draw areas”, which the plus on the camera track offers too.
  2. Drag a rectangle on the display. That is your first area.
  3. Draw more, move existing ones or change them at the corners.
  4. Click “Done”. The editor plays the new move once.

Each area then sits as a clip of its own on the camera track, “Area 1”, “Area 2” and so on. The same number sits in the rectangle on the display. On the track you drag when it comes up and for how long. A clip stops at its neighbors instead of pushing them aside.

Placing the camera freely#

Not everything is a rectangle on the display. Around the device, from below or the wide shot, you set up directly. For that, the plus on the camera track offers “Add shot”. A strip above the stage says which mouse button does what. You place the camera with it and click “Done” in the strip, and the editor plays the move to it once. On the camera track it sits as a “Shot” with its number between the areas, and the camera travels to it just as smoothly. “Adjust camera” on an area turns it into such a shot, and “Draw as area” in its clip’s menu turns it back into an area. Changing the mode or starting playback also ends the adjusting.

How the camera moves#

  • The camera takes two seconds to move into an area and then holds still. How long it takes is set on the clip under “Approach”, faster down to 0.2 seconds or slower up to the whole clip.
  • There may be a gap between two areas. The camera holds the last view there.
  • Before the first area it sits on the camera you set. That is why a new area lines up after the last entrance, so a device can fly in first.
  • After the last area it travels back to the camera you set. This way back sits on the camera track as “Return move”, and you drag its right edge to make it longer or shorter. Drag the last area all the way to the end and the film ends on the close-up.
  • Areas never overlap. The camera cannot be in two places at once.

For the whole camera move#

With an area selected, the right-hand column shows “Adjust camera”, “Redraw area”, its timing and approach, and below that, under “Whole camera move”, what applies to all of them at once. The clip’s menu offers the same actions, plus “Move playhead to start”.

SettingWhat it does
View directionOnly with drawn areas. “Angled in front” looks at the display with depth, “Straight from the front” looks straight at it.
Distribute evenlyFrom two clips on, gives every area and shot the same time again, and the start and end of the move stay where they are.

While it runs#

In animation mode the camera move drives the camera, and you cannot drag it there. A strip above the stage says “The camera moves on its own.” Every way out sits right next to it, “Adjust camera” as a word and the rest as icons with a tooltip.

ButtonWhat it does
Adjust cameraLets you set the camera of the area at the playhead with the mouse, and that area becomes a “Shot”. Before the first area and after the last one, the button switches to camera mode instead, because there the stage shows the view the move starts and ends in.
ReshuffleDifferent viewpoints on the same areas. Keep pressing until it fits.
Edit areasOpens the drawing of the areas on the display again.
Remove camera moveDeletes all areas and shots. The camera then stands still, and you move it yourself again.

Reshuffling only exists with drawn areas and the “Angled in front” viewing direction, editing only with drawn areas. In camera mode you still set the view the move starts from and returns to.

Note

Areas and screenshots belong together. If the images on the display change while the camera moves from area to area, you have a walkthrough. “Camera follows screenshots” in Screens and media builds exactly that in one step.